Traditionally developed to copy a classic appearance (as encountered on antique stringed instruments such as violins and violas) Sunburst is truly a timeless guitar finish commonly encountered upon guitars old and contemporary. It's a greatly sought after finish but it it possible for the inexperienced? It's possible to produce a sunburst finish on your own instrument once you adhere to some simple tips and take your time and don't rush. It's good to practice to begin with using a discarded bit of lumber before attempting on your electric guitar.
If it's a completely new electric guitar kit, then you should construct the actual guitar before anything else. Needless to say you're going to be pulling it down to work on the finish nevertheless, you need to know that you will not berunning into trouble with the guitar that endanger the finish which you have just put so much effort into. Once you've assembled the guitar and analyzed for potential issues you should begin to set up the timber. Sand right back until you have a totally consistent finish to utilize. Then you should remove excess debris and tidy the guitar thoroughly.
The next step is to administer a quantity of wood grain filler. It is best to smear thickly across the face of your electric guitar then work it in. The moment it has dried remove the excess and remove excess with a damp scrap of cotton material. Now it's an opportunity to apply paint to the back and sides of the body and neck of your electric guitar. A critical point to bear in mind is to conceal the top and neck area. If you end up spraying paint or lacquer it's recommended that you keep the spray packs in warm water before putting in use. It should require a range of coats for this reason you shouldn't consider applying too much in one fell swoop. The key is to increase your hue layer upon layer and spray from a respectable distance away in order to achieve a gentle edge. The nearer you end up being the more complicated the edge line you will end up with.
Following that administer the amber lacquer. Chances are you'll need to cover the sides of the guitar after which you can position the guitar on your decent work bench facing upwards before applying. When you've carried out this step you should administer the clear coat next and sand in between coats to eradicate any runs. After that apply the next pitch-dark stain to get a transition of colour in between the edge and midsection colors. Attempt to apply especially thin and amass the necessary coats. At this point be sure to let the most recent coat harden off. The moment the guitar is completely free of moisture focus on sanding all over again.
This really is the final part. The secret to success here is to make use of a more lightweight measure of emery paper each time you end up being basically taking off the marks because of the gauge of sandpaper administered before soon after which progressing for the lightweight gauge. Continue to keep delicately sanding and then migrating to a lighter gauge unless you run out of sandpaper after which you can proceed to your buffer.About now you may basically continue to keep buffing or hand polishing until you get completely fine for the finished look.
If it's a completely new electric guitar kit, then you should construct the actual guitar before anything else. Needless to say you're going to be pulling it down to work on the finish nevertheless, you need to know that you will not berunning into trouble with the guitar that endanger the finish which you have just put so much effort into. Once you've assembled the guitar and analyzed for potential issues you should begin to set up the timber. Sand right back until you have a totally consistent finish to utilize. Then you should remove excess debris and tidy the guitar thoroughly.
The next step is to administer a quantity of wood grain filler. It is best to smear thickly across the face of your electric guitar then work it in. The moment it has dried remove the excess and remove excess with a damp scrap of cotton material. Now it's an opportunity to apply paint to the back and sides of the body and neck of your electric guitar. A critical point to bear in mind is to conceal the top and neck area. If you end up spraying paint or lacquer it's recommended that you keep the spray packs in warm water before putting in use. It should require a range of coats for this reason you shouldn't consider applying too much in one fell swoop. The key is to increase your hue layer upon layer and spray from a respectable distance away in order to achieve a gentle edge. The nearer you end up being the more complicated the edge line you will end up with.
Following that administer the amber lacquer. Chances are you'll need to cover the sides of the guitar after which you can position the guitar on your decent work bench facing upwards before applying. When you've carried out this step you should administer the clear coat next and sand in between coats to eradicate any runs. After that apply the next pitch-dark stain to get a transition of colour in between the edge and midsection colors. Attempt to apply especially thin and amass the necessary coats. At this point be sure to let the most recent coat harden off. The moment the guitar is completely free of moisture focus on sanding all over again.
This really is the final part. The secret to success here is to make use of a more lightweight measure of emery paper each time you end up being basically taking off the marks because of the gauge of sandpaper administered before soon after which progressing for the lightweight gauge. Continue to keep delicately sanding and then migrating to a lighter gauge unless you run out of sandpaper after which you can proceed to your buffer.About now you may basically continue to keep buffing or hand polishing until you get completely fine for the finished look.
About the Author:
Read more posts onGuitar Kits visit our site: www.eguitarkits.com the best place on the net for information about Guitar Kits
No comments:
Post a Comment